A miter saw is the tool for tasks that need exact lumber as well as moulding cuts– especially angles. The device named for cutting miters does so much extra.
Sorts Of Miter Saws
With a board level on the base of a miter saw, any angled cut across the large face counts as a "miter" on any miter saw. Turn the board on its edge, area it versus the fence, and also you'll cut a "bevel." A lot of saws cut from 90 to 45 degrees in both instructions, and also some saws can reduce up to 55-degree angles.
Saws start to vary when you consider their blade diameter– typically 10 inches or 12 inches. The bigger the blade, the much deeper and also broader its optimum cut. Typically, a 10-inch miter saw will certainly reduce a 2 x 6 at 90 degrees and also a 2 x 4 at 45 levels; a 12-inch miter saw will cut a 2 x 8 at 90 degrees as well as a 2 x 6 at 45 degrees.
Saws additionally differ by whether the blade arm simply revolves (a standard miter saw) or both swings and slides (a moving miter saw). The moving activity can reduce also wider boards. A 12-inch version, for example, will certainly reduce a 2 x 16 at 90 levels as well as a 2 x 12 at 45 levels.
Either can end up being a compound saw– the blade arm both swings at an angle as well as tilts at an angle to the bed of the table to reduce both a bevel and also miter at the same time. This is largely utilized to cut crown moulding.
Reducing with a Miter Saw
The cut angle and timber thickness figure out where the blade will certainly get in touch with the product. When noting a board, prolong the line across the stock, drop the blade to the wood to check your positioning, as well as readjust the board as required prior to beginning the saw.
When you're reducing a board, remainder more than half its size on the saw. If the board is also long, stack a few scraps beside the saw to support the overhanging board. For a timesaving solution, mount your saw on a saw stand with assistances for lengthy supply.
Area the supply against the fencing at the rear of the saw base, and also hold it with your hands (or a clamp) at the very least 6 inches from the blade. Only after that ought to you start the saw.
Always keep your other hand on the saw handle. Both arms need to be straight out in front of you, and also your feet firmly planted.
Never cross your arms when operating the saw.
Begin the saw on top of the operating setting, enable the electric motor to come up to speed, and also bring the saw down into the timber. When the board is reduced completely with, launch the trigger and allow the blade to completely quit before you raise the blade.
Learn the kinds of cuts you can make with a miter saw. Enjoy our Do It Yourself Fundamentals video:
2 Time-Savers
You can accelerate repeated cuts in two methods: As opposed to separately gauging components for the same routes, note the part size on an item of covering up tape affixed to the fence. After that get rid of the tape when you're done.
For even greater precision, connect a quit block. Affix pieces of double-face carpet tape to the back face of a 3/4-inch-thick timber scrap. With the saw unplugged and also the blade down, action from the blade teeth to a factor undecided equivalent to the component size. There, press the taped block against the fencing.
With the end of a board pushed gently against the block, make your cut. Each part you reduced afterwards will certainly be the same length– simply blow away any kind of sawdust that can accumulate against the stop block.
Quick Tips for Miter Saw Success
• Constantly reduced the factory end from a board prior to measuring as well as reducing a part for much better fit and less sanding.
• Allow the saw do the work; do not force the blade through the timber.
• Even more teeth equals smoother cuts. Make use of a blade with more than 50 teeth for building cuts. For great cuts, such as moulding, use a blade with greater than 90 teeth.
• Dealt with lumber typically has a greater wetness web content than construction lumber, so use a reduced tooth matter even for great cuts. The open spaces in between the teeth clear the debris and also put less stress on the motor.
• If possible, reduced one angle end of a part before you note and cut the opposite end.